- #WIFI REPEATER MANUAL MANUAL#
- #WIFI REPEATER MANUAL UPGRADE#
- #WIFI REPEATER MANUAL PASSWORD#
- #WIFI REPEATER MANUAL PC#
Backup and Restore Configuration Settings.Transform Your Existing Wired Network to a Wireless One.Use Your Extender as a Wireless Adapter.Chapter 6 More Features of Your Extender.Manage the Extender via the TP-Link Tether App.Chapter 3 OneMesh with Seamless Roaming.Chapter 1 Get to Know About Your Extender.While the device is power on press and hold the reset button until all LEDs momentarily change, then release the button and wait for the device to reboot. Please reset the Device and go through the configuration again.
#WIFI REPEATER MANUAL PASSWORD#
Please log into the Device's web-based interface to check the password and try again.
You may have entered the incorrect Wi-Fi password of your host Wi-Fi during the configuration. 
What to do if the LEDs do not change to solid after completing setup
Verify that is correctly entered in the web browser and press Enter. Make sure your computer is set to obtain an IP address automatically. Make sure the computer is connected to the extended network SSID or connect to the device using an Ethernet cable. #WIFI REPEATER MANUAL UPGRADE#
It may cause the firmware upgrade to fail and the device will become unusable. Note: Do not interrupt the device, close the web browser or power off the device during a firmware upgrade.
Click Apply and wait a few minutes for the firmware upgrade to be complete. Click Browse to locate the downloaded new firmware file. Enter the older password then enter the new password and click Applyįirmware upgrade can fix bugs related to the device, however it is not recommended to upgrade the firmware if the device is working normally and stable. Go to and login with the default password admin. The default password for the device is admin, it strongly recommended the password is changed from the default. Wireless network settings can be configured from here. Management via Web Browser Wireless basic configuration If the WPS connection fails, please connect the device using a web browser. Note: Some ISP gateways disable the WPS function by default. The corresponding WLAN LEDs should turn on and stay solid, indicating successful connection. The device will reboot, please wait a few minutes. Within 2 minutes, press the WPS button on your host router. Press and hold the WPS button for 6 seconds on the device. Setup - Wi-Fi Repeater Mode Using a WPS (Wi-Fi Protected Setup) If the signal is weak, relocate it closer to the router to achieve a good (or better) signal quality. The location you choose must be within the range of your existing host Wi-Fi. Plug the device into an electrical out about halfway between the host router and the Wi-Fi dead zone. Verify your wireless settings and click The Wi-Fi Signal LEDs should turn on and stay solid, indicating successful connection. Either keep the same SSID as your host Wi-Fi or create a new name for the extended network. Select the Wi-Fi SSID for your router (Host Wi-Fi) and enter the password. Enter admin (all lowercase) in the password field at login. Launch a web browser and type in the address field. Click the Wi-Fi icon in the top right corner of the screen, and connect to the devices network: Wireless-N. 
Click the Wi-Fi icon on the taskbar and connect to the devices network: Wireless-N. Turn on your laptop/PCs Wi-Fi on if off. Disconnect the Ethernet (Wired) connection from your laptop/PC (if applicable). Shift the power switch to ON and wait until the POWER LED is on and solid green. Plug the device into an electrical outlet near your Wi-Fi router. Switch the mode selector to the Repeater position. Setup - Wi-Fi Repeater Mode Using a Web Browser The device gets the address automatically from your host router or ISP DHCP server The device gets the IP address from your Host Router or ISP DHCP server This device supports Router/AP Mode, select the preferred modeĮnter the user Name and Password provided bby your ISP, these fields are case sensitiveĮnter the IP Address, Subnet Mask, Default Gateway and DNS provided by your ISP NOTE: Avoid installing device where it is heavily surround by objects. #WIFI REPEATER MANUAL PC#
Slow Flashing: The device is trying to connect to a PC or Phoneįast Flashing: The device is connecting to a AP/Router OFF: The device is not receiving electrical powerįlashing: Transferring data to/from a network device
#WIFI REPEATER MANUAL MANUAL#
Note: Images in this manual may differ from the look of the purchased device.
0 kommentar(er)
